Types of Erosion

Water! Water is all over the place, and it moves wherever it wants. Water has the ability to cause major problems at high velocity during certain times such as high rain events that cause flooding. Erosion is an unfortunate result of the damage that moving water can cause. Erosion can be especially present on construction sites due to the exposed sediment and piles of material, and so it is important to know the different types of erosion and the best management practices that can be used to prevent sediment from eroding off site and into the waters of the state. In this month’s Development Digest, we dive into the most common types of erosion found on construction sites.
Generally, there are 4 common forms of erosion that are caused by the movement of water on exposed sediment on construction sites. These 4 forms are splash erosion, sheet erosion, rill erosion, and gully erosion.

• Splash erosion: Splash erosion is very simple and straight forward. Anytime a raindrop hits the ground, specifically exposed sediment, it can hit the sediment and loosen up the soil particles. This is an issue because when the soil particles get loosened, flowing water can easily carry them on downstream. Splash erosion is the first step in the process that if unchecked can lead to very large and costly amounts of erosion.
• Sheet erosion: Sheet erosion is defined as the uppermost layer of the soil being gradually removed do to some environmental factor. The most common cause for sheet erosion on construction sites is rainfall. Rain hits the bare soil loosening up the soil particles and the water then carries those particles off site through runoff.
• Rill erosion: Rill erosion is similar to sheet erosion; however, the erosion is a little more defined into smaller channels. In this type of erosion, the entire surface of the soil is not necessarily being eroded away because the water is forming into small paths and eroding sediment from those concentrated areas. Rill erosion can lead to much worse erosion if left unfixed.
• Gully erosion: Finally, the last type of erosion is the biggest and most easily seen type of erosion. Gully erosion forms from all of those little rills that have been carved into the ground by the water. Eventually, all of those rills meet somewhere and all of the water from the rills get combined into one big channel. This channel is called a gully. A gully has a higher velocity than rill erosion due to the greater amount of water flowing through, and because of this, a gully can be, and in most cases is, the deepest type of erosion. In general, gully erosion can be about 6-12 inches minimum, and at most can be many feet deep depending on the underlying soil and the different soil layers. Once gully erosion starts, it can get much bigger and bigger, and if left untouched and can cause damage to the landscape and anything that could be affected by the land being lost to flowing water.
  

During construction, it is very important to utilize the BMPs (best management practices) available to all of us to prevent erosion from happening. The most important practice available is stabilization. Whether it be through phased grading to minimize disturbance, keeping straw covering the ground during temporary pauses in work, or immediate stabilization of a site at final grade, getting exposed sediment covered up and stabilized is the best thing we can do to minimize the risk of erosion. There are also other practices that we can use if stabilization is not an option due to ongoing construction. BMPs such as silt fence, mulch berm, and filter sock are great for the perimeter of a site and can be used to slow down water and prevent any eroded sediment from moving further downhill and causing more damage. Check dams consisting of rock are great in areas of concentrated flow to slow down the velocity of water and prevent erosion. Overall, limiting the area of disturbed soil on a site can go a long way to limit the amount of erosion that may occur. Being mindful and aware of the work that we do to the land, and what effects it might have, is important. The less care we have about sediment and erosion control, the more damage erosion can do to the land and to the water, so hopefully by now having a basic understanding of the types of erosion out there, we can do our part as humans to protect the soil and keep it in place.

Have questions about sediment and erosion control, or just about erosion in general? Please contact our office and we’d be happy to answer any questions you may have!
​
Article written by Urban/Ag Technician Seth Byerly